Kenwood Sw200 Swr Power Meter Manual
- Kenwood SW-2000 HF & 6 Ham Radio Swr/Wattmeter Demonstrated. How to Measure a Transmitter and VSWR with a Power Meter (Spanish Version. How to use a SWR Meter for tuning CB Antennas.
- KENWOOD sw-eoo SWR/POWER METER Features The sw-200 through-type SWR/POWER meter which, in 2 3 4 Component parts and their functions TX connector A UHF connector accepts transmitter output through a Coaxial cable. ANT connector UHF connector for the antenna or dummy load. Coupler bracket Use this to affix the coupler with screws.
Attention! The text in this document has been recognized automatically. To view the original document, you can use the 'Original mode'.
Feb 12, 2012 Radio Accessories Kenwood SW-2000 SWR & Power Meter. The meter would be open circuit, inadvertently damaging a transceiver, Kenwood probably short them when unplugged for this reason. Sun 12th Feb 2012, 16:31 #5. The manual isn't very detailed but what you are saying is the light would not come on just because the switch is set to PEP.
Standby switch
This switch is used when you want to manually con
Last Update: 2008-06-19 18:59 GMT+1. User Image Release Date: May 29th 2008. Links Official Links konamistyle beatmaniaIIDX14 GOLD (PS2) (Japan) User Image beatmaniaIIDX14 GOLD (PS2) (Japan) Official Site User Image beatmaniaIIDX14 GOLD (PS2) (Japan) Score Collection Information. Download Beatmania IIDX 14 - Gold NTSC-J Part1/2 • Playstation 2 Isos @ The Iso Zone • The Ultimate Retro Gaming Resource. Beatmania iidx 14 gold ps2 iso games.
trol transmit or receive.
SEND:
Places the radio into transmit.
REC:
Places the radio into receive.
The Standby switch is also used to clear an entry dur
ing direct entry of VFO frequencies, or when entering
a memory channel.
@ ALC/PWR/SWR meter switch
ALC meter
Used to monitor the drive level in USB, LSB, and AFSK
modes.
PWR meter
Used to indicate the output power. Note that this meter
is a peak reading meter, not an average reading meter.
SWR meter
Used to indicate the Standing Wave Ratio of the an
tenna and feedline connected to the ANT connector
when the AUTO/THRU switch is in the THRU position.
@ ATT (Attenuator) switch
The incoming receive signal level is attenuated by ap
proximately 20 dB when this switch is activated.
When the incoming receive signal is very strong (20
dB over S-9), the signal should be attenuated to pre
vent distortion of the signal, thereby stabilizing the
receiver performance. This is easily done by activat
ing the ATT switch. This control is also useful when
a strong signal is near your desired signal, while some
loss will occur to the desired signal as well as the un
desired signal, the use of the attenuator will sometimes
allow you to complete the QSO.
NB (Noise Blanker) switch
When pulsating noise, such as that caused by automo
bile ignitions is encountered, place the NB switch ON.
This will provide approximately 40 dB's of attenuation
to this interfering signal. If there is no noise present,
the switch should be in the OFF position. This switch
will not help to eliminate atmospheric or line noises,
only pulse type noise.
VOICE switch
When the optional VS-1 voice synthesizer unit is in
stalled
the
operating
frequency
will
announced
whenever the VOICE switch is depressed. For a dial
frequency
of
14.200.0
the
frequency
Digital Swr Power Meter
will
be
an
nounced
as:
'one',
'four',
'point',
'two',
'zero',
'zero', 'zero', 'zero'.
Please refer to page 28 for installation instructions con
cerning the VS-1 Voice Synthesizer.
Radio Shack Swr Power Meter
Attention! The text in this document has been recognized automatically. To view the original document, you can use the 'Original mode'.
■ SW-100A/100BSWR/POWER meter
Compact and lightweight SWR/POWER/VOLT meters
cover 1.8 ~ 150 MHz (SW-100A), 140 ~ 450 MHz
(SW-1OOB) in range of 1 50W full scale for mobile use.
SW-100A/100B
■ SWT-1 Antenna tuning unit
The SWT-1 (2m band) is an antenna tuning unit designed
for use in conjunction with an SWR/POWER meter to al
low efficient transmission. This unit is especially con
venient for monitoring SWR, using a KENWOOD SWR/
POWER meter.
SWT-1
44